Oh, up above it says "slight shake", hahaha, software stabilizers will not work well if the repaired footage has to assume the same pixel dimensions.The only way to make it fit the original is to use "zooming" and then you get the "jello" effect, which is worse than cropping.If you can play it at crop size, you're better off. This is done quite often on TV, so it's not weird.If you're going to upsample it, I would do that to the whole clip first, then stabilize it, then crop it down to original. That way the whole think looks uniform.So the way that would work is to SCALE down the good footage, and CROP the stabilized part, get it? Read that again and think about it.:)Imagine a 720p rectangle overlayed on a 1080p clip. The rectangle is your target pixel aspect ratio.As you scrub along, the stabilized frames will pass by, and you want to crop them into the rectangle. There should be adequate clearance from the rough edges or rings, or whatever.
I'm going to reshoot the video because the whole thing was just a wreck. Hopefully it'll be back up Ina week or 2.
Ok thanks guys, some concepts I may use in the future.
I know it's an old thread but I have a question and hopefully someone can help. I tried to stabilize a shot taken with mobile phone want to use it for education. So I stabilized it and got an very visible jello effect.
I tacked, stabilized and than zoomed to stablized footage to fit into the Screen. Does it bring better results to first scale it and than crop it?
And if so, how do i do it in Hitfilm? I suggest upscaling a footage inside a comp, embedding that com into another and tracking it there. But comps cannot be tracked, right? So do I Need to Export that scaling as an intermediate footage and Import that one for tracking?
If you have jello, then there is nothing more Hitfilm can do for your footage. As you have found, once you stabilise your shot the jello that was always there becomes more obvious.
ProDad do the Mercalli range of stabilising software that specifically deals with jello. It tracks the image contents and squashes and stretches the image in the opposite direction to the jello to counteract it. There are demo versions with watermarks, demos with no watermark but limited length, and cheap versions with fewer features, so you can check them out and see what suits your budget or needs.
@Juda1 @Palacono has made an error.
Hitfilm Express has a "Rolling Shutter" add-on designed to reduce "Jell-O(tm)" artifacts. It can be purchased as part of the "Repair Pack" add-on in the Hitfilm Store.
Rolling Shutter is included in Hitfilm Pro.
I haven't done a direct comparison, but wouldn't be surprised if Mercalli did a better job than the Hitfilm version, but the Repair pack also has other useful filters in it.
Oops, I forgot about that one. I didn't have much success with it because I had no idea what the settings were going to adjust and it was quite processor intensive on my system. Skew removal worked OK, but maybe my footage was too far gone to get a good result with vertical squash'n'stretch removal. Maybe you'll have better luck. The Denoise Effect included in the Repair Pack is a lot better than any others I've used, so that's something to consider too. Here's the relevant section from the manual. You could check it out on your footage with a demo of Hitfilm Pro - export is disabled.
Some capture methods used by video cameras produce an effect called rolling shutter. This is particularly common with DSLR cameras. Rolling shutter can be identified by a wobbling, jelly-like instability in the frame during rapid movement.
The rolling shutter effect is designed to counteract rolling shutter, correcting the video and minimizing the effects of rolling shutter.
Shutter direction is used to define whether the camera uses a vertical or horizontal shutter. Consult your camera's specifications for more information.
The correction property is used to specify the amount of time it takes for the camera's shutter to travel across the frame.
In the case of cameras using a vertical shutter, this is defined as the time it takes in frames to capture from the top row of the image to the bottom row.
Positive values indicates the vertical shutter is travelling from top to bottom, while negative values are for bottom to top. You should consult the specifications of your camera to find the correction value to use.
This property determines which part of the rolling shutter frame should be used to fix the image.
Rolling shutter works by tracking the movement of every pixel in the frame using optical flow techniques.
The View menu can be used to observe the accuracy of the optical flow track.
Different videos may require adjustments to the optical flow properties. Adjusting the Window size and Sigma properties tend to yield the best results.
@Palacono, I remembered it was there, but didn't remember what it was called. I was poking around in pro for five minutes before it occured to me to check the Repair Pack on the Store.
@Juda1 I agree with Palacono. The Video Noise Reducer in the Repair add-on (and Pro) is as good as NEAT Video, which is a commercial plug-in costing between $75 and $250(!) depending on the version. NEAT Video is the best I've ever used and has been my noise reducer of choice for a decade. Saying Hitfilm's is as good (maybe better!) is very high praise.
Sign in to comment
You have successfully subscribed to the newsletter.
You can unsubscribe from newsletters at any time.
© 2018 FXhome Limited. All rights reserved. "FXhome", "PhotoKey" and "HitFilm" are trademarks of FXhome Limited.