But how do you change the "value"?
You adjust the speed value of the speed effect.
In this screen shot the speed value is set .50 = 50% = half speed. Values above 1.0 speed up playback. 2.0 is twice speed. If you want to change the playback speed over time then you keyframe the speed value.
If you want to speed up audio + video, click on your clip on your timeline with right button and choose Speed/Duration, then change the percentage and click ok.
Where is the speed effect?
aha ya just found it but how tf u u get it to speed up without lag
Great question @EhItsDaveProductions! I hadn't realized I could effect speed here in HitFilm. I usually do it over in Resolve.
If i change the speed to, for example, 3.0 from the Speed/Duration menu thing, the video gets laggy. I have not yet tried the other speed thing, but i could do it to test if it works better.
@SjadowhunterFI by changing speed to 3, you've changed the speed to 3 frames/sec. If by "laggy" you mean "choppy," well... Assuming your original video was 30 fps you've made it 10 times slower. Hitfilm is merely remapping frames, not doing optical flow or other transformations. You cannot expect super smooth slow motion from Hitfilm without shooting high frame rate to begin with, and you can never expect super smooth slow motion at 3 fps.
To interpolate normal footage into super slow motion, the best tool is Twixtor. That's a $300 program. Bear in mind Twixtor lists Hitfilm as a host. That's HITFILM PRO ONLY. Express can NOT use third-party plug-ins.
Thanks for the tips!
Is there also a way to make speed increase smoothly? I mean make it speed up and then slow down again? Or go from normal playing to gradually slower until slow motion then speed up again?
@AKBouwens Yes, there is. The "Speed" Effect.
Now, the Speed Effect is a pain in the butt. Try and follow along here. When you drop a clip on a Layer the In and Out points of the clip define a frame range for the clip. The Speed Effect, being an effect modifies the frames AFTER being defined. What this means is that changing the In point of a clip (trimming after applying the speed effect) will absolutely mess up your keyframes.
There are four ways (and three methods) of changing a clip's speed in Hitfilm. The first is by right-clicking on a media clip in the media bin, selecting "Properties," unchecking "from file" on the frames per second field, the setting a new frame rate. If the original frame rate was 30, setting 60 doubles the speed of the clip, setting 15 halves the speed of the clip. Second is by right-clicking a clip on the timeline and selecting "Speed/Duration." This is similar to defining the speed of a clip in the media bin. The third is using the Rate Stretch Tool and the fourth is the Speed Effect.
The Speed Effect is the only one of the four that can be keyframed, thus the only one that can be used to do speed ramping.
But, as mentioned above, the Speed Effect is a real pain.
To do a speed ramp, this is the procedure I would recommend. For this example, I'm assuming you're moving from normal speed to half speed and back up again. I'm also assuming you're doing most of this on the Editor Timeline.
Trust me, this is the easiest way to deal with speed ramping in Hitfilm. If you try to do it all in one clip with the Speed Effect it's really a pain. Any edits at one end tend to mess up what you want the keys to do at the other end. In fact, when using the Speed Effect it's always best to make the affected clip into an embedded Composite Shot. That way, if you need to trim the end points of the clip, you trim the Comp Shot while leaving the Speed effect baked in.
thanks for the lengthy and thorough reply, I am going to try this!
how to speed up without the music going to speed? too
why is hitfilm just making a empty screen when i put the speed to 20(max) and just showing the select thing, not the actual video?
@NERFFILMS Because the Speed effect also changes the viewable length of the clip. Higher speeds make it play faster and end sooner, so the part you're seeing that's blank is most likely past the end of the clip at its new speed and length. Scrub earlier in time and you should see your video.
You can also make composite shot where you change the speed of the video only. Then you use the composite shot you just created in your timeline. the audio should be unaffected.
Speeding up causes a lag in the timeline but after you finalize the video it should play at high speed without the lag. Like someone mentioned, when you speed up you increase the fps and your video card may not be able to handle it in the program but it will play normal.
You have successfully subscribed to the newsletter.
You can unsubscribe from newsletters at any time.
© 2018 FXhome Limited. All rights reserved. "FXhome", "PhotoKey", "Imerge" and "HitFilm" are trademarks of FXhome Limited.